Skip to Content

Changes for page Power controller

Last modified by Mathias Larsen on 2026/09/24 21:21
From version 32.18
edited by Mathias Larsen
on 2026/09/23 15:31
Change comment: (Autosaved)
To version 33.4
edited by Mathias Larsen
on 2026/09/23 15:35
Change comment: (Autosaved)

Summary

Details

Page properties
Content
... ... @@ -18,14 +18,6 @@
18 18  
19 19  {{toc/}}
20 20  
21 -== ==
22 -
23 -== ==
24 -
25 -== ==
26 -
27 -== ==
28 -
29 29  == Pinout ==
30 30  
31 31  === Connector pinout ===
... ... @@ -69,8 +69,6 @@
69 69  |(% style="width:281px" %)34|(% style="width:135px" %)24V|(% style="width:157px" %)reserve|(% style="width:132px" %)
70 70  |(% style="width:281px" %)35|(% style="width:135px" %)24V|(% style="width:157px" %)sensor card|(% style="width:132px" %)
71 71  
72 -
73 -
74 74  === Microcontroller Pinout ===
75 75  
76 76  The power controller uses a microcontroller to control the pumps, fans, buzzer, and brake light. It also features current monitoring and LED indicators. The Microcontroller used in this system is STM32G431CBT6
... ... @@ -153,12 +153,11 @@
153 153  
154 154  Mateksys PM20S-2 Power Module was used as a quick fix to ensure that it had 12V for the competion.
155 155  
156 -
157 157  === 5V and 3V3 supply ===
158 158  
159 159  Is
160 160  
161 -== Controll logic ==
150 +== Control logic ==
162 162  
163 163  === LED light ===
164 164  
... ... @@ -172,7 +172,6 @@
172 172  
173 173  PUMPS
174 174  
175 -
176 176  == ==
177 177  
178 178  == ==
... ... @@ -253,8 +253,6 @@
253 253  |LM5148RGYR|3.5-80V Current Mode Synchronous Buck Controller, 24-VQFN|U801|1|Texas Instruments|LM5148RGYR
254 254  |ASE-8.000MHz-E-T|Crystal Oscillator, 8MHz, 3.3V, 15pF, 4-Pin SMD|Y1|1|Abracon|ASE-8.000MHZ-E-T
255 255  
256 -
257 -
258 258  = AR27 Concept =
259 259  
260 260  Here is the for AR27
... ... @@ -265,16 +265,17 @@
265 265  ** more dedicate supply circuits
266 266  ** Keep the same current
267 267  ** Adjust the signal led resistor on the PCB
268 -* ​​​​​​​Digital signals
254 +* Digital signals
269 269  ** Adjust the signal led resistor on the PCB
270 270  * 12V supply
271 -** 3 seprate 12 V supply
257 +** 3 seprate 12 V supply
272 272  *** Pump1
273 273  *** Pump2
274 274  *** Inverter/ other 12Vsupply
275 -* Autonomous​​​​​​​​​​​​​​​​​​​​​
261 +* Autonomous​​​​​​​​​​​​​​
276 276  ** Supplied by ASMS
277 277  ** Potentially control ASSI
264 +** ASMS state detection
278 278  
279 279  == Supply table ==
280 280