Skip to Content

Changes for page Sensor Module

Last modified by Heimir Thordarson on 2026/07/05 12:56
From version 11.5
edited by Heimir Thordarson
on 2026/01/21 13:59
Change comment: There is no comment for this version
To version 5.1
edited by Heimir Thordarson
on 2026/01/20 18:46
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,29 +1,16 @@
1 -{{wikibox title="Sensor Module" image="https://wiki.alignracing.no/bin/download/Electrical/Sensor%20Module/WebHome/ASM_AR26.png?rev=1.1" caption="3D model of the Sensor Module from Altium Designer" width="22" labelWidth="50"}}
2 -Voltage = 4.5V - 40V
3 -Fuse Current = 125mA
4 -Sensor Inputs = 13
5 -Voltage divider Inputs = 2
6 -3V3 Thermistor Inputs = 7
7 -5V Pressure Inputs = 4
1 +{{wikibox title="Sensor Module" image="ASM_AR24.PNG" caption="blah bla"}}
2 +Voltage = 12V - 24V
3 +Max Current = 300mA
8 8  {{/wikibox}}
9 9  
10 10  = Description =
11 11  
12 -The Sensor module is designed to measure any extra analog signals rear of the firewall. For AR26, the module is designed to measure two suspension displacement sensors, two oil temperature, four water pressure, four water temperature, and one air temperature sensor. All of the measurements are then transmitted to a CAN network, which there are two of.
8 +The Sensor module is designed to measure the analog
13 13  
10 +== Features ==
11 +
14 14  = Wiring Diagram =
15 15  
16 -In the following section, how the sensor module is connected will be covered. The connector for the sensor module is a [[High-Density d'sub-44>>https://www.te.com/en/product-2311770-1.html]] which is directly solderen onto the circuit board. The plug needed for this system is the [[204517-3>>doc:Sandbox.TestPage3]], which uses crimps instead of solder cups which is common for the dsub connectors
17 -
18 -[[image:AR26_ASM pinout.png||height="221" width="469"]]
19 -
20 -In the figure above, the pinout shows how the pins are divided. Each box shows which pins belong together for each usecase, where the red box is the power input. Yellow boxes are for each canbus network, while the green box is for each sensor used in AR26.
21 -
22 -|=Pin Number|=(((
23 -1
24 -)))|=2|=3|=4|=5|=6|=7|=8|=9|= |= |= |= |= |=
25 -|Pin Name| | | | | | | | | | | | | | |
26 -
27 27  == Typical Application ==
28 28  
29 29  = Design =
AR26_ASM pinout.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.117349330247369537212
Size
... ... @@ -1,1 +1,0 @@
1 -38.5 KB
Content
ASM_AR26.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.117349330247369537212
Size
... ... @@ -1,1 +1,0 @@
1 -145.2 KB
Content
ASM_AR24.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.117349330247369537212
Size
... ... @@ -1,0 +1,1 @@
1 +145.2 KB
Content